Ürün arama
Açıklama
Planet IGS 5226 4P2T Endüstriyel PoE Switch
Özellikler
Physical Port
- 6-port 10/100/1000BASE-T dustproof RJ45 copper with 4-port IEEE 802.3at/af Power over Ethernet Injector function
Hardware Conformance
- Complies with IEEE 802.3at Power over Ethernet Plus end-span PSE
- Complies with IEEE 802.3af Power over Ethernet end-span PSE
- Up to 4 ports of IEEE 802.3af/802.3at devices powered
- Supports PoE Power up to 36 watts for each PoE port
- Auto detects powered device (PD)
- Circuit protection prevents power interference between ports
- Remote power feeding up to 100 meters
- PoE Management
- Total PoE power budget control
- Per port PoE function enable/disable
- PoE Port Power feeding priority
- Per PoE port power limitation
- PD classification detection
- PD alive check
- PoE schedule
- PD scheduled power recycling
- IP50-rated metal case
- Redundant power design
- 48 to 56V DC, redundant power with polarity reverse protect function
- Active-active redundant power failure protection
- Backup of catastrophic power failure on one supply
- Fault tolerance and resilience
- DIN-rail and wall-mount design
- Supports 6000V DC Ethernet ESD protection
- -40 to 75 degrees C operating temperature
- Layer 3 IP Routing Features
- Supports maximum 32 static routes and route summarization
Layer 2 Features
- Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
- High performance of Store-and-Forward architecture, and runt/CRC filtering that eliminates erroneous packets to optimize the network bandwidth
- Storm control support
- Broadcast/Multicast/Unicast
- Supports VLAN
- IEEE 802.1Q tagged VLAN
- Up to 255 VLANs groups, out of 4095 VLAN IDs
- Provides Bridging (VLAN Q-in-Q) support (IEEE 802.1ad)
- Private VLAN Edge (PVE)
- Protocol-based VLAN
- MAC-based VLAN
- IP subnet-based VLAN
- Voice VLAN
- Supports Spanning Tree Protocol
- IEEE 802.1D Spanning Tree Protocol (STP)
- IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)
- IEEE 802.1s Multiple Spanning Tree Protocol (MSTP), spanning tree by VLAN
- BPDU Guard
- Supports Link Aggregation
- 802.3ad Link Aggregation Control Protocol (LACP)
- Cisco ether-channel (static trunk)
- Maximum 3 trunk groups, with 2 ports for each trunk
- Up to 4Gbps bandwidth (full duplex mode)
- Provides port mirror (many-to-1)
- Port mirroring monitors the incoming or outgoing traffic on a particular port
- Loop protection to avoid broadcast loops
- Supports E.R.P.S. (Ethernet Ring Protection Switching)
- IEEE 1588 and Synchronous Ethernet network timing
Quality of Service
- Ingress shaper and egress rate limit per port bandwidth control
- 8 priority queues on all switch ports
- Traffic classification
- IEEE 802.1p CoS
- ToS/DSCP/IP precedence of IPv4/IPv6 packets
- IP TCP/UDP port number
- Typical network application
- Strict priority and Weighted Round Robin (WRR) CoS policies
- Traffic-policing policies on the switch port
- DSCP remarking
Multicast
- Supports IGMP snooping v1, v2 and v3
- Supports MLD snooping v1 and v2
- Querier mode support
- IGMP snooping port filtering
- MLD snooping port filtering
- MVR (Multicast VLAN Registration)
Security
- Authentication
- IEEE 802.1x port-based/MAC-based network access authentication
- IEEE 802.1x authentication with guest VLAN
- Built-in RADIUS client to cooperate with the RADIUS servers
- RADIUS/TACACS+ users access authentication
- Access Control List
- IP-based Access Control List (ACL)
- MAC-based Access Control List (ACL)
- Source MAC/IP address binding
- DHCP Snooping to filter distrusted DHCP messages
- Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
- IP Source Guard prevents IP spoofing attacks
- IP address access management to prevent unauthorized intruder
Management
- IPv4 and IPv6 dual stack management
- Switch Management Interfaces
- Telnet command line interface
- Web switch management
- SNMP v1, v2c, and v3 switch management
- SSH/SSL secure access
- IPv6 address/NTP management
- Built-in Trivial File Transfer Protocol (TFTP) client
- BOOTP and DHCP for IP address assignment
- System Maintenance
- Firmware upload/download via HTTP/TFTP
- Reset button for system reboot or reset to factory default
- Dual images
- DHCP relay and option 82
- User privilege levels control
- NTP (Network Time Protocol)
- Link Layer Discovery Protocol (LLDP) and LLDP-MED
- Network diagnostic
- Cable diagnostic technology provides the mechanism to detect and report potential cabling issues
- ICMPv6/ICMPv4 remote ping
- SMTP/Syslog remote alarm
- Four RMON groups (history, statistics, alarms and events)
- SNMP trap for interface link up and link down notification
- System Log
- PLANET Smart Discovery Utility for deployment management
Teknik Özellikler
| Hardware Specifications | |
| Copper Ports | 6 10/100/1000BASE-T dustproof RJ45 auto-MDI/MDI-X ports | 
| PoE Injector Port | 4 ports with 802.3at/af PoE injector function (Port-3 to Port-6) | 
| Power Connector | 1 x M12, 5-pin A-Coded male connector | 
| Switch Architecture | Store-and-Forward | 
| Switch Fabric | 12Gbps/non-blocking | 
| Throughput | 8.9Mpps@64bytes | 
| Address Table | 8K entries, automatic source address learning and aging | 
| Shared Data Buffer | 4M bits | 
| Flow Control | IEEE 802.3x pause frame for full-duplex | 
| Back pressure for half-duplex | |
| Jumbo Frame | 9K bytes | 
| Reset Button | < 5 sec: System reboot | 
| > 5 sec: Factory default | |
| Dimensions (W x D x H) | 132 x 75 x 160 mm | 
| Weight | 809g | 
| Enclosure | IP50 metal case | 
| Installation | Wall-mount and DIN rail kit | 
| LED | System: | 
| PWR1 (Green), PWR2 (Green), Fault (Red) | |
| Ring (Green), R.O. (Green) | |
| 10/100/1000T RJ45 Interfaces (Port 1 to Port 2): | |
| LNK/ACT (Green) | |
| 10/100/1000T RJ45 Interfaces (Port 3 to Port 6): | |
| LNK/ACT (Green) | |
| PoE-in-Use (Orange) | |
| Power Consumption | Max. 165.3 watts/563.67 BTU | 
| Power Requirements | Dual 48~56V DC (>53V DC for PoE+ output recommended) | 
| ESD Protection | 6KV DC | 
| Power over Ethernet | |
| PoE Standard | IEEE 802.3af/802.3at PoE/PSE | 
| PoE Power Supply Type | End-span | 
| PoE Power Output | IEEE 802.3af Standard | 
| - Per port 48V~53V DC (depending on the power supply), max. 15.4 watts | |
| IEEE 802.3at Standard | |
| - Per port 53V~56V DC (depending on the power supply), max. 36 watts | |
| Power Pin Assignment | 1/2(+), 3/6(-) | 
| PoE Power Budget | 144 watts max. (depending on power input) | 
| PoE Ability | PD @ 7 watts: 4 units | 
| PD @ 15.4 watts: 4 units | |
| PD @ 30.8 watts: 4 units | |
| Layer 2 Management Functions | |
| Port Configuration | Port disable/enable | 
| Auto-negotiation 10/100/1000Mbps full and half duplex mode selection | |
| Flow control disable/enable | |
| Port Status | Display each port’s speed duplex mode, link status, flow control status, auto-negotiation status, trunk status | 
| Port Mirroring | TX/RX/Both | 
| Many-to-1 monitor | |
| VLAN | 802.1Q tagged based VLAN | 
| Q-in-Q tunneling | |
| Private VLAN Edge (PVE) | |
| MAC-based VLAN | |
| Protocol-based VLAN | |
| Voice VLAN | |
| IP Subnet-based VLAN | |
| MVR (Multicast VLAN registration) | |
| Up to 255 VLAN groups, out of 4095 VLAN IDs | |
| Link Aggregation | IEEE 802.3ad LACP/static trunk | 
| 3 groups with 2 ports per trunk | |
| Spanning Tree Protocol | IEEE 802.1D Spanning Tree Protocol (STP) | 
| IEEE 802.1w Rapid Spanning Tree Protocol (RSTP) | |
| IEEE 802.1s Multiple Spanning Tree Protocol (MSTP) | |
| QoS | Traffic classification based,strict priority and WRR | 
| 8-level priority for switching: | |
| - Port number | |
| - 802.1p priority | |
| - 802.1Q VLAN tagging | |
| - DSCP/ToS field in IP packet | |
| IGMP Snooping | IGMP (v1/v2/v3) snooping, up to 255 multicast groups | 
| IGMP querier mode support | |
| MLD Snooping | MLD (v1/v2) snooping, up to 255 multicast groups | 
| MLD querier mode support | |
| Access Control List | IP-based ACL/MAC-based ACL | 
| Up to 256 entries | |
| Bandwidth Control | Per port bandwidth control | 
| Ingress: 100Kbps~1000Mbps | |
| Egress: 100Kbps~1000Mbps | |
| Layer 3 Functions | |
| IP Interfaces | Max. 8 VLAN interfaces | 
| Routing Table | Max. 32 routing entries | 
| Routing Protocols | IPv4 software static routing | 
| IPv6 software static routing | |
| Management | |
| Basic Management Interfaces | Telnet, Web browser, SNMP v1, v2c | 
| Secure Management Interfaces | SSH, SSL, SNMP v3 | 
| SNMP MIBs | RFC 1213 MIB-II | 
| RFC 1493 Bridge MIB | |
| RFC 1643 Ethernet MIB | |
| RFC 2863 Interface MIB | |
| RFC 2665 Ether-Like MIB | |
| RFC 2819 RMON MIB (Groups 1, 2, 3 and 9) | |
| RFC 2737 Entity MIB | |
| RFC 2618 RADIUS Client MIB | |
| RFC 2863 IF-MIB | |
| RFC 2933 IGMP-STD-MIB | |
| RFC 3411 SNMP-Frameworks-MIB | |
| RFC 4292 IP Forward MIB | |
| RFC 4293 IP MIB | |
| RFC 4836 MAU-MIB | |
| IEEE 802.1X PAE | |
| LLDP | |
| Power over Ethernet MIB | |
| Standards Conformance | |
| Regulatory Compliance | FCC Part 15 Class A, CE | 
| Stability Testing | IEC 60068-2-32 (free fall) | 
| IEC 60068-2-27 (shock) | |
| IEC 60068-2-6 (vibration) | |
| Railway Traffic | *EN50155 | 
| Standards Compliance | IEEE 802.3 10BASE-T | 
| IEEE 802.3u 100BASE-TX | |
| IEEE 802.3ab Gigabit 1000T | |
| IEEE 802.3x flow control and back pressure | |
| IEEE 802.3ad port trunk with LACP | |
| IEEE 802.1D Spanning Tree Protocol | |
| IEEE 802.1w Rapid Spanning Tree Protocol | |
| IEEE 802.1s Multiple Spanning Tree Protocol | |
| IEEE 802.1p Class of Service | |
| IEEE 802.1Q VLAN tagging | |
| IEEE 802.1X Port Authentication Network Control | |
| IEEE 802.1ab LLDP | |
| IEEE 802.3af Power over Ethernet | |
| IEEE 802.3at Power over Ethernet Plus | |
| IEEE 802.3az EEE (Energy Efficient Ethernet) | |
| RFC 768 UDP | |
| RFC 793 TFTP | |
| RFC 791 IP | |
| RFC 792 ICMP | |
| RFC 2068 HTTP | |
| RFC 1112 IGMP v1 | |
| RFC 2236 IGMP v2 | |
| RFC 3376 IGMP v3 | |
| RFC 2710 MLD v1 | |
| FRC 3810 MLD v2 | |
| ITU-T G.8032 ERPS (Ethernet Ring Protection Switching) | |
| Environment | |
| Operating | Temperature: -40 ~ 75 degrees C | 
| Relative Humidity: 5 ~ 95% (non-condensing) | |
| Storage | Temperature: -40 ~ 80 degrees C | 
| Relative Humidity: 5 ~ 95% (non-condensing) | |
| Standard Accessories | |
| Packet Contents | 6 x Waterproof RJ45 Connector | 
| 1 x M12 5-pin A-coded female connector power cable, 1.2m | |
| 1 x Wall-mount kit | |
| 1 x DIN-rail kit | |
| 1 x M12 Power Waterproof Cap | |
| 1 x Quick Installation Guide | |
 Planet IGS 5226 4P2T Endüstriyel PoE Switch Pdf Dosyası3.03 MB
Planet IGS 5226 4P2T Endüstriyel PoE Switch Pdf Dosyası3.03 MB
Teknik Kısa
 PoE :  PoE  
 Port Hızı :  1 GBit  
 Yönetilebilirlik :  Yönetilebilir Layer 2 Plus  
 Aktarım Port Sayısı :  2  
 Montaj Tipi :  Wall Mount  
 PoE Port Sayısı :   4 Port
 4 Port  
 4 Port
 4 Port   PoE Güç Bütçesi :  130-200 Watt  
 Aktarım Türü :  Rj45  


